Difference between revisions of "GWR 17410 'Toad' 20T Goods Brake Van"

From SVR Wiki
Jump to: navigation, search
m (Link added)
(Restoration update)
Line 34: Line 34:
 
Much of the steelwork, the entire wooden floor and most of the side/end/roof planking needs replacing.  The tyres need to be turned to remove flats. Vacuum cylinder, brakegear pins and bushes must be refurbished. A new stove and roof canvass will be essential.
 
Much of the steelwork, the entire wooden floor and most of the side/end/roof planking needs replacing.  The tyres need to be turned to remove flats. Vacuum cylinder, brakegear pins and bushes must be refurbished. A new stove and roof canvass will be essential.
  
The GWR drawing of the missing sanding gear has been located. It may prove possible to join with other Toad owners in a scheme to construct a batch of replacements.
+
The GWR drawing of the missing sanding gear has been located. It may prove possible to join with other Toad owners in a scheme to construct a batch of replacements. However evidence from other preserved Toads of this wartime series suggests that they may have been built without sanding gear.
  
 
It is intended to restore it to as near original condition as reasonably possible, and in GWR livery, but BR bauxite has not been ruled out as a possibility for the future.  
 
It is intended to restore it to as near original condition as reasonably possible, and in GWR livery, but BR bauxite has not been ruled out as a possibility for the future.  
Line 42: Line 42:
 
New veranda side and end plates,underfloor support plates, kerb rails and corner posts were made and fitted by Mawley Engineering Ltd between 18-20th October 2016 to replace the thoroughly rotten originals. However the very prominent waist level angle irons, the two vertical "T" sections at the end, and the two side door slam posts were in good condition and have been refurbished and re-used. The new structure was seal welded to prolong its life expectancy, but volunteers have commenced the time consuming job of drilling the new steelwork for snap head rivets which will maintain the authentic look.
 
New veranda side and end plates,underfloor support plates, kerb rails and corner posts were made and fitted by Mawley Engineering Ltd between 18-20th October 2016 to replace the thoroughly rotten originals. However the very prominent waist level angle irons, the two vertical "T" sections at the end, and the two side door slam posts were in good condition and have been refurbished and re-used. The new structure was seal welded to prolong its life expectancy, but volunteers have commenced the time consuming job of drilling the new steelwork for snap head rivets which will maintain the authentic look.
  
Fortunately the steelwork at the van end seems to be mostly restorable, and after emptying many broken drawhooks and worn out brake blocks from the sandboxes and ballast bin (under the end windows and hatch), the rust and life expired end section of kerb rail were removed. The floor plate (and hence the end of the body) had been lifted about half an inch by rust scale which was removed prior to the said plate being seam welded to the headstock to prevent a repetition. A replacement kerb rail and floor strengthening angle iron were also welded in place. The steel lower van sides were suffering from rust due to water ingress, and a new system is being tried, involving more steel angle, seam welded to the top inside edge of the original steel plates. It'll be invisible, and hopefully improve 17410's longevity.  
+
Fortunately the steelwork at the van end seems to be mostly restorable, and after emptying many broken drawhooks and worn out brake blocks from the sandboxes and ballast bin (under the end windows and hatch), the rust and life expired end section of kerb rail were removed. The floor plate (and hence the end of the body) had been lifted about half an inch by rust scale which was removed prior to the said plate being seam welded to the headstock to prevent a repetition. A replacement kerb rail and floor strengthening angle iron were also welded in place. The steel lower van sides were suffering from rust due to water ingress, and a new system is being tried, involving more steel angle, seam welded to the top inside edge of the original steel plates. It'll be invisible, and hopefully improve 17410's longevity. In May 2017 the new floor was installed.
 
 
To finance the restoration The SVR Charitable Trust is seeking donations and component sponsorship, both of which can be Gift Aided. A form can be accessed by clicking on the link [http://www.lnersvrcoachfund.org.uk/Donations_and_Gift_aid_TOAD_17410_form.pdf SVR Charitable Trust TOAD Donation Form].Thank you. 
 
  
 +
To finance the restoration The SVR Charitable Trust is seeking donations and component sponsorship, both of which can be Gift Aided. A form can be accessed by clicking on the link [http://www.lnersvrcoachfund.org.uk/Donations_and_Gift_aid_TOAD_17410_form.pdf SVR Charitable Trust TOAD Donation Form].Thank you.
  
 
==Gallery==
 
==Gallery==

Revision as of 18:18, 27 May 2017

GWRGreat Western Railway 17410 'ToadGWR telegraphic code signifying a goods brake van, which became the standard design's nickname' 20T Goods Brake Van
GWR 17410 20150320.jpg
GWRGreat Western Railway ToadGWR telegraphic code signifying a goods brake van, which became the standard design's nickname Brake Van 17410
Built By GWRGreat Western Railway Swindon
Status Under restoration
Number 17410
History
Built 1940
Type Brake van
Telegraphic code ToadGWR telegraphic code signifying a goods brake van, which became the standard design's nickname
Brakes Vacuum fitted
1970 Entered preservation on SVRSevern Valley Railway
2016 Restoration begun

Goods Wagons

20 ton 'ToadGWR telegraphic code signifying a goods brake van, which became the standard design's nickname' Brake Van 17410 was built at Swindon in 1940, one of a batch of 100 financed by the War Department but taken straight into GWRGreat Western Railway stock. The diagram number was AA.21, lot number 1370. It was vacuum fitted with screw couplings. An original stencil on an internal wall suggests that its first allocation was to Cardiff, but when last in SVRSevern Valley Railway service it was lettered in late GWRGreat Western Railway style grey livery and allocated to "Bristol RU".

At some stage in its life the sanding gear was removed, and its place was taken by additional ballast presumably to increase its adhesion weight. Several other preserved Toads have undergone the same modification.

History

It arrived on the SVRSevern Valley Railway in November 1970, purchased by a group of working members known as the 17410 Fund, and was restored the following year, after which it saw regular use by the PWPermanent Way Department. Following withdrawal as surplus to PWPermanent Way requirements and in very poor condition it languished in Bewdley yard, but in December 2015 its restoration, by the LNER Carriage Group, started. In early 2016 the 17410 Fund transferred ownership to the SVR Charitable Trust for restoration and continued preservation on the SVRSevern Valley Railway.[1] The van is known to many on the SVRSevern Valley Railway as "Don Wilcox's toad". Once restored its hoped to use it as a fitted brake van on demonstration freight trains, filming and photo charters, and for brake van rides, for which it will be most suitable.

Restoration

Much progress with its restoration has been made, the continued rate of which will depend largely on the raising of funds for materials. A new pair of veranda side doors and replacement opening window frames have been made, and the end hatch is being restored. The layers of paint were removed from the interior, when it was found that its first, "as built" internal finish was scumble grained in imitation beech and cedar with a light oak ceiling. The number 17410 was stenciled opposite the guard's seat in pink lettering, with the word "CARDIFF" (presumably its first allocation) below. Its later (presumed BRBritish Rail or British Railways) interior finish was off white (ivory) and bauxite with a white ceiling. Regular progress reports and detailed pictures are posted on LNER(SVR)Coach Fund Toad Progress Page

Much of the steelwork, the entire wooden floor and most of the side/end/roof planking needs replacing. The tyres need to be turned to remove flats. Vacuum cylinder, brakegear pins and bushes must be refurbished. A new stove and roof canvass will be essential.

The GWRGreat Western Railway drawing of the missing sanding gear has been located. It may prove possible to join with other ToadGWR telegraphic code signifying a goods brake van, which became the standard design's nickname owners in a scheme to construct a batch of replacements. However evidence from other preserved Toads of this wartime series suggests that they may have been built without sanding gear.

It is intended to restore it to as near original condition as reasonably possible, and in GWRGreat Western Railway livery, but BRBritish Rail or British Railways bauxite has not been ruled out as a possibility for the future.

During the summer/autumn of 2016, the vacuum brake cylinder and handbrake pedestal were removed to safe storage and the rotten steel veranda sides and underfloor platework were consigned to the scrapheap. A considerable amount of (very necessary) weld repair was then carried out by a skilled volunteer on the exposed section of underframe, ballast bins and bases of the cabin and side door posts.[2][3] A heavy job completed in early October was the emptying, cleaning, strengthening, painting and re-filling of all eight underfloor ballast bins.

New veranda side and end plates,underfloor support plates, kerb rails and corner posts were made and fitted by Mawley Engineering Ltd between 18-20th October 2016 to replace the thoroughly rotten originals. However the very prominent waist level angle irons, the two vertical "T" sections at the end, and the two side door slam posts were in good condition and have been refurbished and re-used. The new structure was seal welded to prolong its life expectancy, but volunteers have commenced the time consuming job of drilling the new steelwork for snap head rivets which will maintain the authentic look.

Fortunately the steelwork at the van end seems to be mostly restorable, and after emptying many broken drawhooks and worn out brake blocks from the sandboxes and ballast bin (under the end windows and hatch), the rust and life expired end section of kerb rail were removed. The floor plate (and hence the end of the body) had been lifted about half an inch by rust scale which was removed prior to the said plate being seam welded to the headstockThe underframe member across each end of a wagon carrying the buffers and coupling. Known as the Bufferbeam on a locomotive. to prevent a repetition. A replacement kerb rail and floor strengthening angle iron were also welded in place. The steel lower van sides were suffering from rust due to water ingress, and a new system is being tried, involving more steel angle, seam welded to the top inside edge of the original steel plates. It'll be invisible, and hopefully improve 17410's longevity. In May 2017 the new floor was installed.

To finance the restoration The SVRSevern Valley Railway Charitable Trust is seeking donations and component sponsorship, both of which can be Gift Aided. A form can be accessed by clicking on the link SVR Charitable Trust TOAD Donation Form.Thank you.

Gallery

See also

List of goods wagons
Rolling stock currently under restoration

References

17410 on the Railway Heritage Register Wagon Survey
SVRSevern Valley Railway Stock Book Eighth Edition

  1. Public Notice GWR ‘Toad’ 17410, dated 01/09/2015, accessed 10/11/2015
  2. NatPres forum SVR Wagons Thread
  3. 17410 restoration updates on www.lnersvrcoachfund.org.uk

Links

17410 on www.vintagecarriagestrust.org
GWR Toad 17410 on www.lnersvrcoachfund.org.uk